Obrázek může být reprezentace.
Viz Specifikace pro podrobnosti o produktu.
STFI24N60M2

STFI24N60M2

Introduction

The STFI24N60M2 is a power MOSFET belonging to the category of semiconductor devices. This device is commonly used in various electronic applications due to its unique characteristics and functional features.

Basic Information Overview

  • Category: Power MOSFET
  • Use: The STFI24N60M2 is used as a switching device in power electronics applications.
  • Characteristics: It exhibits low on-state resistance, high switching speed, and low gate charge, making it suitable for high-efficiency power conversion.
  • Package: The STFI24N60M2 is typically available in a TO-220 package.
  • Essence: It serves as a crucial component in power supply circuits and motor control systems.
  • Packaging/Quantity: It is commonly packaged in reels or tubes, with varying quantities based on manufacturer specifications.

Specifications

  • Voltage Rating: 600V
  • Current Rating: 24A
  • On-State Resistance: 0.24Ω
  • Gate Charge: 48nC
  • Operating Temperature Range: -55°C to 150°C
  • Package Type: TO-220

Detailed Pin Configuration

The STFI24N60M2 typically has three pins: 1. Gate (G): Used to control the switching operation of the MOSFET. 2. Drain (D): Connected to the load in the circuit. 3. Source (S): Connected to the ground or return path of the circuit.

Functional Features

  • Low On-State Resistance: Enables efficient power transfer with minimal voltage drop.
  • High Switching Speed: Facilitates rapid switching transitions, reducing power loss.
  • Low Gate Charge: Allows for quick and precise control of the MOSFET.

Advantages and Disadvantages

Advantages

  • High efficiency in power conversion applications.
  • Fast switching capability.
  • Low conduction losses.

Disadvantages

  • Susceptible to damage from voltage spikes.
  • Sensitive to static electricity during handling.

Working Principles

The STFI24N60M2 operates based on the principle of field-effect transistors, where the application of a voltage at the gate terminal controls the flow of current between the drain and source terminals. By modulating the gate voltage, the MOSFET can efficiently switch high-power loads.

Detailed Application Field Plans

The STFI24N60M2 finds extensive use in the following applications: - Switched-mode power supplies - Motor drives - Inverters - Uninterruptible power supplies (UPS) - Electronic ballasts

Detailed and Complete Alternative Models

Some alternative models to the STFI24N60M2 include: - IRFP460: Similar voltage and current ratings - FDPF18N50: Lower voltage rating but comparable current handling capacity - IXFN24N100: Higher voltage rating and lower on-state resistance

In conclusion, the STFI24N60M2 power MOSFET offers high performance and reliability in various power electronics applications, making it a preferred choice for efficient power management and control.

Word Count: 414

Seznam 10 běžných otázek a odpovědí souvisejících s aplikací STFI24N60M2 v technických řešeních

  1. What is STFI24N60M2?

    • STFI24N60M2 is a power MOSFET designed for high-speed switching applications.
  2. What are the key features of STFI24N60M2?

    • The key features include a low on-state resistance, high dv/dt capability, and a fast recovery body diode.
  3. What are the typical applications of STFI24N60M2?

    • Typical applications include power supplies, motor control, and lighting ballasts.
  4. What is the maximum voltage and current rating for STFI24N60M2?

    • The maximum voltage rating is 600V and the maximum current rating is 24A.
  5. Does STFI24N60M2 require a heat sink for operation?

    • It is recommended to use a heat sink for higher power dissipation applications to ensure optimal performance and reliability.
  6. What is the thermal resistance of STFI24N60M2?

    • The thermal resistance from junction to case (RthJC) is typically specified in the datasheet.
  7. Can STFI24N60M2 be used in parallel to increase current handling capability?

    • Yes, STFI24N60M2 can be used in parallel to increase current handling capability in high-power applications.
  8. What are the important parameters to consider when designing with STFI24N60M2?

    • Important parameters to consider include gate drive voltage, gate charge, and input/output capacitance.
  9. Is STFI24N60M2 suitable for automotive applications?

    • STFI24N60M2 is not specifically designed for automotive applications and may not meet automotive-grade requirements.
  10. Where can I find the detailed specifications and application notes for STFI24N60M2?

    • Detailed specifications and application notes can be found in the product datasheet provided by the manufacturer.